Reducing Failure Rates with Proper Material Selection and Testing

Tensile Strength Test

A failed polyurethane component can cost far more than the material used to make it. A production line may stop. Finished products may need to be reworked or replaced. A customer may begin questioning whether the next shipment will perform as expected.

For OEMs and manufacturers, reducing that risk starts before full-scale production. Proper material selection, application-specific material testing, and consistent polyurethane quality control help identify potential problems while there is still time to address them.

The goal is to establish that a material fits the application, can be processed reliably, and continues to meet agreed requirements.

Start with the Conditions the Material Will Face

Choosing a polyurethane system requires a clear picture of how the finished product will be made and used. A material selected primarily for hardness, density, or initial price may leave other critical requirements unresolved.

Before comparing formulations, define:

  • Mechanical demands: Will the material experience abrasion, impact, sustained loading, repeated compression, or flexing?
  • Environmental exposure: Will it encounter moisture, chemicals, outdoor weathering, or temperature extremes?
  • Production requirements: What equipment, processing temperatures, working time, and cure schedule must the system accommodate?
  • Performance limits: What changes in dimensions, appearance, or function would make the finished product unacceptable?

Consider a component that must remain compressed during service. Initial hardness alone does not establish whether it will recover sufficiently after the load is removed. Likewise, room-temperature performance does not answer every question about behavior in a hot, wet, or chemically demanding environment.

A complete application profile gives the development team a stronger basis for selecting both the formulation and the tests used to evaluate it.

Make Material Testing Relevant to the Application

An effective test plan begins with a practical question: How could this product fail?

The answer helps determine which properties to measure, which exposures to reproduce, and what constitutes an acceptable result. Depending on the material and application, evaluation may include strength, elongation, tear resistance, abrasion resistance, compression behavior, dimensional stability, or adhesion.

For example, compression-set testing evaluates residual deformation after specified compression conditions. Liquid-exposure testing can help assess changes in properties following contact with selected fluids. The appropriate methods depend on the material and intended service.

Agree on acceptance criteria before testing begins. “Good chemical resistance” is too broad to guide a decision. Identify the chemical, concentration, exposure temperature, contact duration, and acceptable changes in relevant properties.

Standardized tests provide a consistent basis for comparison. Application-specific evaluations help determine whether those results address the demands of the finished product. Both have a role in reducing uncertainty.

Validate the Material in Your Manufacturing Process

A promising laboratory result is an important development milestone. Production trials establish whether that performance can be reproduced using the equipment, part geometry, and processing conditions intended for manufacturing.

Evaluate the system under representative conditions, including the specified mix ratio, material temperatures, mixing method, and cure requirements. Where relevant, include the actual substrate or mold configuration.

Trials should also examine the practical production window. How sensitive is the process to permitted variations in temperature or timing? Can operators consistently achieve the required results at the planned production rate?

Finding a processing issue during a controlled trial gives the team an opportunity to adjust the formulation, equipment settings, or procedures before it creates widespread scrap or missed deliveries.

Use Polyurethane Quality Control to Maintain Consistency

Initial qualification and ongoing quality control answer different questions.

Qualification asks whether the selected system can meet the application’s requirements. Polyurethane quality control checks whether subsequent production continues to meet established specifications.

An appropriate quality plan may include incoming raw material checks, defined manufacturing controls, and batch testing of selected properties. Depending on the system, those checks might address viscosity, reactivity, density, or cured physical properties.

Documented methods and acceptance limits make results easier to interpret. Batch traceability connects material records to production history, supporting a more focused investigation if a concern arises.

Routine release testing does not need to repeat every development test. It should monitor the characteristics selected to verify consistency, with additional evaluation when changes could affect qualified performance.

Treat Changes as a Reason to Reassess

A qualified material may need further evaluation when the application changes.

A different chemical exposure, higher operating temperature, revised part design, or faster production cycle can introduce demands that the original test plan did not address. Changes to materials or processing should also prompt a review of what needs to be revalidated.

Keeping engineering, production, quality, and the material supplier involved helps teams identify those implications before the revised product reaches customers.

Protect Cost, Uptime, and Customer Confidence

Material selection and testing require an investment, but they also create opportunities to catch problems before those problems become warranty claims, production interruptions, or damaged customer relationships.

Carlisle Polyurethane Systems works with OEMs and manufacturers to evaluate application requirements, develop polyurethane solutions, and troubleshoot performance challenges. Early collaboration helps connect material decisions with manufacturing needs and end-use expectations.

Developing a new product or addressing recurring material concerns? Contact Carlisle Polyurethane Systems to discuss your application, processing requirements, and performance goals.

Need something else? We’re here to help.

Need something else?
We’re here to help.

Connect with our knowledgeable representatives to talk project specs, challenges, recommendations and more.